Feature of FluoroSurf |
|
* High performance for anti humid, water proof. * High resistant to lithium battery electrode * High resistant to acid gas and liquid * High insulation * Low dielectric constant * Non flammable liquid |
FLUOROSURF forms a thin film with high moisture-proof, salt water resistant, water-proof, acid-proof, lithium battery electrolyte resistant, and water/oil repellent properties and other protection functions. It has also high insulation resistance, low dielectric constant and other electric properties and is most appropriate for electronic component water-proofing, insulation protection and mounting printed circuit board moisture and water proof coating.
- ■In comparison with urethane and acrylic moisture-proof coating agents, its moisture-proof performance is four times higher and the thin film can sufficiently ensure moisture-proof effect. Weight increase by the coating film is restricted and therefore this is optimum for light-weight mobile and other devices.
- ■It is resistant to lithium battery electrolyte, protects the board against leakage of electrolyte and prevents firing.
- ■It provides high protection effect against acid gas, salt solution and corrosive solutions and prevents corrosion.
- ■It contains no silicone or other low-molecular compound and causes no contact failure of electric contact points after being coated.
- ■The agent dries at room temperature in 5 seconds to 30 minutes. Heating is not required.
- ■The non-flammable solvent does not catch fire and its toxicity is low. It is not subject to the PRTR Law (JAPAN)and Fire Defense Law(JAPAN).
- ■It’s viscosity is low easy to handle. It does not make the workplace dirty.
- ■The pot life is semi-permanent, without wastefulness.
- ■Soldering and other repair are possible.
| ＊Moisture and water proof coat over mounting boards of smart phone and other mobile devices |
| ＊Moisture and water proof coat over mounting boards of smart phone and other mobile devices |
| ＊Coating to protect board from lithium battery electrolyte (firing prevention) |
| ＊Metal ion migration (diffusion) prevention |
| ＊Water and moisture proof coating over mounting board of air conditioner outdoor unit, water heater and other exterior devices |
| ＊Coating to protect boards of devices in the toilet, kitchen and other water sections |
| ＊Coating to protect electronic board and metal components from sulfur gas |
| ＊LED sulfuration control coating |
| Surface resistivity | Volume resistivity | Permittivity | Dielectric tangent | dielectric strength |
| 1.6×10 16Ω･㎝ | 2.9×10 16Ω･㎝ | 2.25 | 0. 0285 | 85KV/mm |
| 85℃ 85%RH DC10V 500hr | 85℃ 85%RH DC10V 500hr | 1GHz | 1GHz | 25℃ 35%RH |
＊These data is measured about the film of FG-3030 1micron meter.
【 Moisture Proofness Comparison Data （JIS-Z-0208 40DegC 90%RH ) 】
| Kind of coating | Film Thickness(μｍ) | Moisture permeability (g/m2/24hr) |
| FluoroSurf FG-3030TH-8.0 | 8 | 640 |
| Urethane coating | 40 | 670 |
| FluoroSurf FG-3030-30 | 30 | 220 |
| Acrylic coating | 100 | 230 |
| Silicone coating | 1000 | 350 |
| FluoroSurf FG-3030-20 4times | 120 | 37 |
■Film of only about 8 microns presents moisture-proofness of the same degree as that of conventional coating agent of 40 microns. When the film thickness is the same, moisture permeability is approximately 1/3 to 1/4 of that of conventional products.
【Salt Water Proofness (Insulation Breakdown)】
■This test result suggests the extra patience of our fluorine resin against insulation breakdown by salt water in comparison with general insulation urethane resin.
| Item | Film thickness | Time to insulation breakdown | Leakage current at insulation breakdown |
| FLUOROSURF FG-3030-20 | 15-20μm | 146min. | 0.8μA |
|
Urethane coating agent of other manufacturer |
15-20μm | 3 sec. | 1000μA or more |
Test Method
- Coat the surface of each comb-shaped electrode wiring board of slit width of 200 microns respectively with various coating agents and leave them more than 1 hour to dry.
- 2. Drop 3-5ml of 5% salt water across slits and apply voltage of 18 to 19VDC through the wiring as shown in the left figure.
- While applying voltage, check the energization condition with an ammeter (measurement limit 0.01μA) until the salt water dries completely.
- If the leakage voltage exceeds 1000μA, stop the test immediately.
- ■Various specifications (resin concentration) of film thickness from 0.1 to 40 microns or more can be provided to meet versatile requirements.
- ■Coating liquid is non-flammable , as it is safe to use and not subject to the Fire Defense Law and PRTR Law.
- ■Soldering and other repair are possible.
- ■Blue coloring and fluorescent specifications are optionally available to be used to check the film. (When black light is irradiated, the film shines and can be recognized.)
| Product Model No. | Application / Feature | Film thickness (micron meter) |
| FS-1610 | Acid proof, Water /Oil Repellent, Protect contact point, | 0.1-8 |
| FG-3030 | Anti moisture film for Mounting Board, Acid proof, Resistance for electrolyte , LED protect from acid gas Soft film It forms soft film for Mounting board. |
0.1-40 |
| FG-3650 | Anti moisture film for Mounting Board, Acid proof, Resistance for electrolyte , LED protect from acid gas Soft film It forms soft film for Mounting board. |
0.1-40 |
| FG-5040 | Hard film (Pencil Hardness 3H) Anti acid | 0.1-10 |
Only representative FLUOROSURF products are presented here.
A diversity of products may be offered to meet any requirements. Please inquire of us about details .
E-mail:info@fluorotech.co.jp » Please click for demand samples
Our products are chemical products for industrial use.
They may have an influence on the health depending on handling manner.
For this reason, our products or their samples are not offered for personal use.
We would like you to accept such our intention.
